Difference between revisions of "VCR Commander with Floodcam Setup"

Revision as of 22:23, 20 March 2006

Questions

How do I program my VCR Commander with a Floodcam?

Answer

Follow the instructions below to setup your VCR Commander.

Learn IR (Infrared)

Unplug the Infrared cable from the VCR Commander, and grab your remote and motion sensor.

Press and hold the "Power" button on the VCR Commander until the red light is solid (it flashes 13 times). This clears the unit of any previously learned codes.

Press and hold the "Record" button on the VCR Commander until the light is solid; then release. This puts the Commander into learning mode.

Press and release "Record" on the VCR Commander (it begins flashing 8 times; then the light is solid).

Press "Record" on your VCR remote (holding it no further than 1/4 inch away from eye on back of commander).

When it learns the Record function, the light on the Commander will flash off and come back on solid.

Press and release "Stop" on the VCR Commander (it flashes 8 times; then remains solid).

Press "Stop" on the VCR remote (holding it no further than 1/4 inch away from the eye on back of the VCR Commander).

When it learns the Stop function, the light on the Commander will flash off once and come back on solid. Wait until this light goes out before doing anything else (should take 10 seconds).

IF THE VCR COMMANDER FLICKERS AND GOES OUT DURING PROGRAMMING, BEGIN AGAIN AT #2

To clear the VCR Commander of Motion Sensor radio frequency codes and start from scratch:

Press and hold "Play" on the VCR Commander until the red light is solid.

Press and release "Play" (the light goes out).

Learn Floodcam Motion Sensor

Press and hold "Play" on the VCR Commander until its light is solid.

Walk out to where your Floodcam is located and trigger it by moving or waving your hand in front of the motion sensor.

Plug in the Infrared emitter cable, and position 1 of the 3 emitters � inch to the left or right of the VCR Infrared Input. Only use one of them.

Press and release "Stop" on the VCR Commander. If the light on the Commander is out, it is in Home mode. To switch modes, press and hold the "Stop" button; when the light becomes solid, release. It should now be in Away mode and ready. The Commander should flash every 1-1.5 seconds. When motion is detected, if the VCR is not triggered to record, re-position the emitter, and press and release "Stop" on the Commander again.

Alternate Instructions

Initial Configuration

Detach the IR emitter cable.
Attach the D9100 power supply to the UX23A and plug it into a standard outlet. You may also insert 4 �C� size batteries if desired.

Programming the IR Codes

You will require your existing VCR remote control to perform the following steps.

Push and hold the RECORD button on the UX23A until the LED on the UX23A illuminates.

Release the RECORD button on the UX23A, then quickly push and release the same �Record� button one time. The UX23A will begin beeping, and the LED will flash approximately eight times then remain solid.

Note: Do not wait more than five seconds between steps 2 and 4.

Position your VCR's remote control no more than an inch away from the clear, IR target located on the back of the UX23A.

Aim the remote at the Infrared target and hold the RECORD button on your VCR's remote. You will hear one beep, and the LED on the UX23A will go out and immediately come back on.

Press and release the �Stop� button on the UX23A. The UX23A will begin beeping and the LED will flash approximately seven times and remain solid. Note: Do not wait more than five seconds between steps 5 and 7.

Position your VCR's remote control no more than an inch away from the clear, IR (Infrared) target located on the back of the UX23A

Aim the remote at the Infrared target and hold the STOP button on your VCR's remote. You will hear one beep, and the LED on the UX23A will go out and immediately come back on.

Allow the UX23A to time out. This will take approximately ten seconds. The IR programming of your UX23A is complete.

Programming the Radio Frequency (Motion Sensor) Codes

Program each Motion Sensor to the desired House/Unit code. Click here for more detailed instructions on Motion Sensors.

Push and hold the �Play� button on the UX23A until the LED on it illuminates.

Walk out to where your Floodcam is located, and trigger it by moving or waving your hand in front of the motion sensor. You will hear one beep, and the LED on the UX23A will go out.

Final Configuration

Attach the IR emitter cable to the UX23A.

Position one of the black IR emitters in front of the IR target window on your VCR (where you normally aim the VCR's remote control).

Verify the VCR is powered on and insert a blank tape.

Trigger the Floodcam's motion sensor.

Your VCR will record for five minutes unless another programmed RF command is received from a motion sensor (at which point the five minute counter will reset and VCR will continue recording).

@@ Line 1: / Line 1: @@
-Questions
+== Questions ==
 How do I program my VCR Commander with a Floodcam?
-Answer
+== Answer ==
 Follow the instructions below to setup your VCR Commander.
-Learn IR (Infrared):
+=== Learn IR (Infrared) ===
 Unplug the Infrared cable from the VCR Commander, and grab your remote and motion sensor.
-*Press and hold the "Power" button on the VCR Commander until the red light is solid (it flashes 13 times). This clears the unit of any previously learned codes.
-*Press and hold the "Record" button on the VCR Commander until the light is solid; then release. This puts the Commander into learning mode.
+#Press and hold the "Power" button on the VCR Commander until the red light is solid (it flashes 13 times). This clears the unit of any previously learned codes.
-*Press and release "Record" on the VCR Commander (it begins flashing 8 times; then the light is solid).
-*Press "Record" on your VCR remote (holding it no further than 1/4 inch away from eye on back of commander).
+#Press and hold the "Record" button on the VCR Commander until the light is solid; then release. This puts the Commander into learning mode.
-*When it learns the Record function, the light on the Commander will flash off and come back on solid.
-*Press and release "Stop" on the VCR Commander (it flashes 8 times; then remains solid).
+#Press and release "Record" on the VCR Commander (it begins flashing 8 times; then the light is solid).
-*Press "Stop" on the VCR remote (holding it no further than 1/4 inch away from the eye on back of the VCR Commander).
-*When it learns the Stop function, the light on the Commander will flash off once and come back on solid.
+#Press "Record" on your VCR remote (holding it no further than 1/4 inch away from eye on back of commander).
-*Wait until this light goes out before doing anything else (should take 10 seconds).
-'''''
+#When it learns the Record function, the light on the Commander will flash off and come back on solid.
-IF THE VCR COMMANDER FLICKERS AND GOES OUT DURING PROGRAMMING, BEGIN AGAIN AT #2'''''
+#Press and release "Stop" on the VCR Commander (it flashes 8 times; then remains solid).
+#Press "Stop" on the VCR remote (holding it no further than 1/4 inch away from the eye on back of the VCR Commander).
+When it learns the Stop function, the light on the Commander will flash off once and come back on solid. Wait until this light goes out before doing anything else (should take 10 seconds).
+'''IF THE VCR COMMANDER FLICKERS AND GOES OUT DURING PROGRAMMING, BEGIN AGAIN AT #2'''
 To clear the VCR Commander of Motion Sensor radio frequency codes and start from scratch:
 *Press and hold "Play" on the VCR Commander until the red light is solid.
 *Press and release "Play" (the light goes out).
-Learn Floodcam Motion Sensor:
+=== Learn Floodcam Motion Sensor ===
 *Press and hold "Play" on the VCR Commander until its light is solid.
 *Walk out to where your Floodcam is located and trigger it by moving or waving your hand in front of the motion sensor.
 Plug in the Infrared emitter cable, and position 1 of the 3 emitters � inch to the left or right of the VCR Infrared Input. Only use one of them.
 Press and release "Stop" on the VCR Commander. If the light on the Commander is out, it is in Home mode. To switch modes, press and hold the "Stop" button; when the light becomes solid, release. It should now be in Away mode and ready. The Commander should flash every 1-1.5 seconds. When motion is detected, if the VCR is not triggered to record, re-position the emitter, and press and release "Stop" on the Commander again.
-'''Alternate Instructions'''
-'''Setup'''
+=== Alternate Instructions ===
-'''Initial Configuration'''
+==== Initial Configuration ====
 *Detach the IR emitter cable.
 *Attach the D9100 power supply to the UX23A and plug it into a standard outlet. You may also insert 4 �C� size batteries if desired.
-'''Programming the IR Codes'''
+==== Programming the IR Codes ====
 You will require your existing VCR remote control to perform the following steps.
-[center][img src="http://graphics.x10.com/images7/vcr_4.gif" border=0>[/center>
-*Push and hold the RECORD button on the UX23A until the LED on the UX23A illuminates.
+http://graphics.x10.com/images7/vcr_4.gif
-*Release the RECORD button on the UX23A, then quickly push and release the same �Record� button one time. The UX23A will begin beeping, and the LED will flash approximately eight times then remain solid. '''Note:''' Do not wait more than five seconds between steps 2 and 4.
-[center][img src="http://graphics.x10.com/images7/vcr_5.gif" border=0>[/center>
-*Position your VCR's remote control no more than an inch away from the clear, IR target located on the back of the UX23A.
+#Push and hold the RECORD button on the UX23A until the LED on the UX23A illuminates.
-*Aim the remote at the Infrared target and hold the RECORD button on your VCR's remote. You will hear one beep, and the LED on the UX23A will go out and immediately come back on.
-*Press and release the �Stop� button on the UX23A. The UX23A will begin beeping and the LED will flash approximately seven times and remain solid. '''Note:''' Do not wait more than five seconds between steps 5 and 7.
+#Release the RECORD button on the UX23A, then quickly push and release the same �Record� button one time. The UX23A will begin beeping, and the LED will flash approximately eight times then remain solid.
-*Position your VCR's remote control no more than an inch away from the clear, IR (Infrared) target located on the back of the UX23A
-*Aim the remote at the Infrared target and hold the STOP button on your VCR's remote. You will hear one beep, and the LED on the UX23A will go out and immediately come back on.
+'''Note:''' Do not wait more than five seconds between steps 2 and 4.
-*Allow the UX23A to time out. This will take approximately ten seconds. The IR programming of your UX23A is complete.
-[a name="rf"][/a]
-'''Programming the Radio Frequency (Motion Sensor) Codes'''
+http://graphics.x10.com/images7/vcr_5.gif
-*Program each Motion Sensor to the desired House/Unit code. Click [a href="http://www.x10.com/instructions/automation_motion_sensors.htm"]here[/a] for more detailed instructions on Motion Sensors.
-*Push and hold the �Play� button on the UX23A until the LED on it illuminates.
-*Walk out to where your Floodcam is located, and trigger it by moving or waving your hand in front of the motion sensor. You will hear one beep, and the LED on the UX23A will go out.
+#Position your VCR's remote control no more than an inch away from the clear, IR target located on the back of the UX23A.
-'''Final Configuration'''
-[center][img src="http://graphics.x10.com/images7/vcr_6.gif" border=0>[/center>
+#Aim the remote at the Infrared target and hold the RECORD button on your VCR's remote. You will hear one beep, and the LED on the UX23A will go out and immediately come back on.
-*Attach the IR emitter cable to the UX23A.
-[center][img src="http://graphics.x10.com/images7/vcr_7.gif" border=0>[/center>
+#Press and release the �Stop� button on the UX23A. The UX23A will begin beeping and the LED will flash approximately seven times and remain solid. '''Note:''' Do not wait more than five seconds between steps 5 and 7.
-*Position one of the black IR emitters in front of the IR target window on your VCR (where you normally aim the VCR's remote control).
-*Verify the VCR is powered on and insert a blank tape.
+#Position your VCR's remote control no more than an inch away from the clear, IR (Infrared) target located on the back of the UX23A
-*Trigger the Floodcam's motion sensor.  Your VCR will record for five minutes unless another programmed RF command is received from a motion sensor (at which point the five minute counter will reset and VCR will continue recording).
-Related Articles
+#Aim the remote at the Infrared target and hold the STOP button on your VCR's remote. You will hear one beep, and the LED on the UX23A will go out and immediately come back on.
-[img src="http://site.x10.com/?Z3gxT2tiYXNlYXJ0aWNsZTEuZGF0=RND|kbasearticle"]
+Allow the UX23A to time out. This will take approximately ten seconds. The IR programming of your UX23A is complete.
+==== Programming the Radio Frequency (Motion Sensor) Codes ====
+#Program each Motion Sensor to the desired House/Unit code. Click [http://www.x10.com/instructions/automation_motion_sensors.htm here] for more detailed instructions on Motion Sensors.
+#Push and hold the �Play� button on the UX23A until the LED on it illuminates.
+#Walk out to where your Floodcam is located, and trigger it by moving or waving your hand in front of the motion sensor. You will hear one beep, and the LED on the UX23A will go out.
+==== Final Configuration ====
+http://graphics.x10.com/images7/vcr_6.gif
+#Attach the IR emitter cable to the UX23A.
+http://graphics.x10.com/images7/vcr_7.gif
+#Position one of the black IR emitters in front of the IR target window on your VCR (where you normally aim the VCR's remote control).
+#Verify the VCR is powered on and insert a blank tape.
+#Trigger the Floodcam's motion sensor.
+Your VCR will record for five minutes unless another programmed RF command is received from a motion sensor (at which point the five minute counter will reset and VCR will continue recording).