Difference between revisions of "Wrist Watch Panic Button"

From X10Wiki
Jump to: navigation, search
Line 1: Line 1:
=Wrist Watch Panic Button=
+
=='''WR10A: Wrist Watch Panic Button'''==
  
The WR10A will work with all Security Consoles and Personal Voice Dialer Consoles currently sold by X10.
+
[[image:WR10A.png]]
 +
 
 +
 
 +
==Product Pages==
 +
 
 +
*[http://www.authinx.com/manuals/X10/AM466.pdf Detailed AM466 Instructions]
 +
*[http://www.x10.com/am446-lamp-module.html Purchase AM466]
 +
*[http://www.x10.com/am446-lamp-module.html Purchase AM466]
 +
 
 +
 
 +
==Specifications== 
 +
 
 +
;Weight:  0.32 lbs. 
 +
;Power Supply:  120VAC @ 60Hz
 +
 
 +
'''NOTE''': The WR10A will work with all Security Consoles and Personal Voice Dialer Consoles currently sold by X10.
  
 
==Installation==
 
==Installation==
Line 10: Line 25:
 
#Set the slide switch on the console to RUN.
 
#Set the slide switch on the console to RUN.
  
===Installation Note=== If you do not hear a beep in step 2 above, remove the battery and then hold down the watch face for 2 seconds. Refit the battery and press ARM again then hold down the watch face for 2 seconds. The WR10A will now have a new code; go back to step 1.
+
 
 +
===Installation Note===
 +
 
 +
If you do not hear a beep in step 2 above, remove the battery and then hold down the watch face for 2 seconds. Refit the battery and press ARM again then hold down the watch face for 2 seconds. The WR10A will now have a new code; go back to step 1.
 +
 
  
 
==Operation==
 
==Operation==
 +
 
#Set the slide switch on the console to RUN.
 
#Set the slide switch on the console to RUN.
 
#Press the face of the WR10A and hold for one second to trip the Panic Alarm. Press twice quickly to stop the Alarm.
 
#Press the face of the WR10A and hold for one second to trip the Panic Alarm. Press twice quickly to stop the Alarm.
 +
  
 
==Replacing Batteries==
 
==Replacing Batteries==
Line 21: Line 42:
 
#Set the slide switch on the console to RUN.
 
#Set the slide switch on the console to RUN.
 
#Press the face of the WR10A and hold for one second to trip the Panic Alarm. If the alarm goes off, the watch is still installed in the console and you do not need to do anything else. Press twice quickly to stop the Alarm.
 
#Press the face of the WR10A and hold for one second to trip the Panic Alarm. If the alarm goes off, the watch is still installed in the console and you do not need to do anything else. Press twice quickly to stop the Alarm.
 +
  
 
==If the console does not trip==
 
==If the console does not trip==
Line 27: Line 49:
 
#Press the face of the WR10A and hold for three seconds. The Console will emit a tone.
 
#Press the face of the WR10A and hold for three seconds. The Console will emit a tone.
 
#Set the slide switch on the console to RUN.
 
#Set the slide switch on the console to RUN.
 +
 +
  
 
[[Image:Wr10a.jpg]]
 
[[Image:Wr10a.jpg]]
 +
 +
 +
[[category: Configuration]]
 +
[[category: Hardware]]
 +
[[category: Product Information]]
 +
[[category: Specifications]]

Revision as of 02:02, 11 June 2014

WR10A: Wrist Watch Panic Button

WR10A.png


Product Pages


Specifications

Weight
0.32 lbs.
Power Supply
120VAC @ 60Hz

NOTE: The WR10A will work with all Security Consoles and Personal Voice Dialer Consoles currently sold by X10.

Installation

The WR10A comes with a CR2016 Lithium 3V battery already installed.

  1. Set the INSTALL/RUN switch on your Console to INSTALL.
  2. Press the face of the WR10A and hold for two seconds. The Console will emit a tone.
  3. Set the slide switch on the console to RUN.


Installation Note

If you do not hear a beep in step 2 above, remove the battery and then hold down the watch face for 2 seconds. Refit the battery and press ARM again then hold down the watch face for 2 seconds. The WR10A will now have a new code; go back to step 1.


Operation

  1. Set the slide switch on the console to RUN.
  2. Press the face of the WR10A and hold for one second to trip the Panic Alarm. Press twice quickly to stop the Alarm.


Replacing Batteries

Remove the back cover and replace the battery with a CR2016 Lithium 3V battery. We recommend doing this in a well-lit area and completely removing the new battery from its packaging before taking the old battery out. After replacing the battery, please test the alarm:

  1. Set the slide switch on the console to RUN.
  2. Press the face of the WR10A and hold for one second to trip the Panic Alarm. If the alarm goes off, the watch is still installed in the console and you do not need to do anything else. Press twice quickly to stop the Alarm.


If the console does not trip

  1. Set the INSTALL/RUN switch on your Console to INSTALL.
  2. Press the face of the WR10A and hold for three seconds. The Console will emit a tone.
  3. Set the slide switch on the console to RUN.


Wr10a.jpg