Difference between revisions of "XCam2 and Vanguard ICC Setup"

Revision as of 19:59, 18 August 2010

Question

How do I set up my XCam2 cameras and Vanguard Internet Control Center?

Answer

Check for Parts

Make sure you have all these items:

If you have more than one camera, you should also have a TM751 transceiver module:

Software Installation

First, download and install Vanguard ICC using the link you received by e-mail. (If you didn't get an e-mail with the link in it, fill out our Secure Download Link Form.)

Click on the software link in the email you received titled "New Software Download Link." Before you download the software, choose the option to save the file, and save it onto your desktop so you can more easily access it later.

Disable or turn off your anti-virus software before you install the software as some anti-virus programs interfere with the installation. Remember to turn on your anti-virus program when you finish these steps.

Go to your desktop and double click the installation program you just downloaded. The software installation process will install the driver for your VA12A.

Once this is done you are ready to install the USB Video Adapter (model VA12A). Do not connect the USB Video Adapter before installing Vanguard ICC.

When the installation program instructs you to, plug the USB Video Adapter into a USB port located directly on the back of your computer:

The computer will recognize that new hardware has been installed and complete the installation. After the installation finishes, plug the CM19A FireCracker PC Transceiver into another USB port.

Error creating thumbnail: /bin/bash: /usr/bin/convert: No such file or directory Error code: 127

First Camera Installation

C) Plug the receiver into wall power. Make sure the receiver is turned on; the power switch is next to the antenna hinge.

Error creating thumbnail: /bin/bash: /usr/bin/convert: No such file or directory Error code: 127

D) Connect the video receiver to the USB Video Adapter. Adjust the paddle-shaped so that it it faces in the general direction of all the cameras -- sometimes it may be best to point the antenna towards the ceiling.

E) Set up a camera.

Plug the power supply into a free AC outlet. Connect the camera to the power supply. The camera should come on and you should be able to get the picture on your PC. Adjust the antenna so that it points better at the antenna of the receiver.

Here is a full one-camera setup:

If you only have one camera, skip to Software Configuration below.

Multiple Camera Installation

A) Choose a House Code - a letter between A and P. Set the House Code on the wireless transceiver module (model TM751), plug it into an AC outlet and extend the antenna.

B) Set the House Code on your remote control (model CR12A, or CR14A) to the selected House Code and insert 4 AAA batteries. If the cameras are going to be units other than 1-4, follow the instructions that came in the remote’s box to change the scan controls.

E) Unplug the camera you have plugged in and set it to the House and Unit code you have selected. You want all the cameras, remotes, and the TM751 on the same House Code; the cameras should be at sequential Unit Codes (usually 1,2,3, etc.) Using your remote, try to switch to a camera that is NOT plugged in (for example, hit 2 ON or C2 if you have just installed a camera at Unit Code 1.) You should see the camera picture go away, indicating that the camera has received the signal from the TM751 transceiver.

F) Repeat step E with the other cameras you have.

Software Configuration

Run the Vanguard software. If you get an error message about the VA12A video adapter, please see this article. Register your software, click on the Option tab, then click on the Cameras subtab:

Click on Camera A1 then change the camera`s type to XCam2 or Ninja, as appropriate. If you have more than one camera, add an entry for each of your cameras, then click OK.

What Next?

Here are some popular support resources for Vanguard:

Vanguard Internet Control Center

Motion Recording In Vanguard ICC

Motion Recording In Vanguard ICC Troubleshooting

Remote Viewing Over the Internet

Installing the Vanguard Web Client

@@ Line 38: / Line 38: @@
 [[image:Cm19aonpc.jpg]]
-===Camera Installation===
+===First Camera Installation===
-A) If you have more than one camera, set the House Code on the wireless transceiver module (model TM751), plug it into an AC outlet and extend the antenna.
-http://graphics.x10.com/images_automation/tm751.jpg
-B) If you have more than one camera, or a Ninja base, set the House Code on your remote control (model CR12A, or CR14A) and insert 4 AAA batteries. If the cameras are going to be units other than 1-4, follow the instructions that came in the remote’s box to change the scan controls.
-[[image:Thumb_cr12a.jpg ]] [[image:Thumb_cr14a.jpg ]]
 C) Plug the receiver into wall power. Make sure the receiver is turned on; the power switch is next to the antenna hinge.
@@ Line 56: / Line 48: @@
 [[image:Connectup.jpg]]
-E) Set up a camera. Set the House and Unit code on the addressable power supply as you chose above (see Getting Started).
+E) Set up a camera.
 http://www.x10.com/images/template/gray/xcam_images/xcam_setup_02.jpg
-Plug the power supply into a free AC outlet. Connect the camera to the power supply. The camera should come on and you should be able to get the picture on your PC. Adjust the antenna so that it points better at the antenna of the receiver. When the camera is set up, turn it off using the CR12A.
+Plug the power supply into a free AC outlet. Connect the camera to the power supply. The camera should come on and you should be able to get the picture on your PC. Adjust the antenna so that it points better at the antenna of the receiver.
-F) Repeat step E for each camera you are setting up.
 Here is a full one-camera setup:
 [[image:Alldone.jpg]]
+If you only have one camera, skip to [[XCam2 and Vanguard ICC Setup#Software Configuration|Software Configuration]] below.
+===Multiple Camera Installation===
+A) Choose a House Code - a letter between A and P. Set the House Code on the wireless transceiver module (model TM751), plug it into an AC outlet and extend the antenna.
+http://graphics.x10.com/images_automation/tm751.jpg
+B) Set the House Code on your remote control (model CR12A, or CR14A) to the selected House Code and insert 4 AAA batteries. If the cameras are going to be units other than 1-4, follow the instructions that came in the remote’s box to change the scan controls.
+[[image:Thumb_cr12a.jpg ]] [[image:Thumb_cr14a.jpg ]]
+E) Unplug the camera you have plugged in and set it to the House and Unit code you have selected. You want all the cameras, remotes, and the TM751 on the same House Code; the cameras should be at sequential Unit Codes (usually 1,2,3, etc.) Using your remote, try to switch to a camera that is NOT plugged in (for example, hit 2 ON or C2 if you have just installed a camera at Unit Code 1.) You should see the camera picture go away, indicating that the camera has received the signal from the TM751 transceiver.
+F) Repeat step E with the other cameras you have.
 ===Software Configuration===