Difference between revisions of "Setting Up the Remote Chime"
Jump to navigation
Jump to search
X10douglas (talk | contribs) |
|||
| (4 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
==Introduction== | ==Introduction== | ||
| + | |||
This guide should help you in quickly setting up the X10 Remote Chime. | This guide should help you in quickly setting up the X10 Remote Chime. | ||
| + | |||
==Setup== | ==Setup== | ||
| + | |||
*Set the House code dial on the SC546A Remote Chime to the same letter as your X10 Controller (TM751 Transceiver Module, MT10A Mini Timer, etc.). | *Set the House code dial on the SC546A Remote Chime to the same letter as your X10 Controller (TM751 Transceiver Module, MT10A Mini Timer, etc.). | ||
| − | *Set the Unit Code dial on the SC546A to any unused number between 1 and 16. If you are using it with a Motion Sensor, set it to the same House | + | |
| + | |||
| + | *Set the Unit Code dial on the SC546A to any unused number between 1 and 16. If you are using it with a Motion Sensor, set it to the same House and Unit Code as your Motion Sensor (MS13A/MS14A/MS16A) and the same House code as your Transceiver (TM751)--if you are using a Transceiver as opposed to the ActiveHome Professional software interface. | ||
| + | |||
| + | |||
*Plug the SC546A Remote Chime into any unused outlet (not one that is controlled by a wall switch, in case the switch accidentally gets turned off). | *Plug the SC546A Remote Chime into any unused outlet (not one that is controlled by a wall switch, in case the switch accidentally gets turned off). | ||
| + | |||
| + | |||
*To test the SC546A, press the number button (on any X10 Controller) corresponding to its Unit Code. Or walk past a Motion Sensor. The Motion Sensor sends a signal to the TM751 (or CM15A interface), which retransmits it over your house wiring to the SC546A. The Remote Chime then sounds. | *To test the SC546A, press the number button (on any X10 Controller) corresponding to its Unit Code. Or walk past a Motion Sensor. The Motion Sensor sends a signal to the TM751 (or CM15A interface), which retransmits it over your house wiring to the SC546A. The Remote Chime then sounds. | ||
| − | ==Related Articles== | + | |
| + | |||
| + | |||
| + | |||
| + | ===Related Articles=== | ||
| + | |||
| + | [[Remote Chime Module]] | ||
[[Category:frequently asked questions]] | [[Category:frequently asked questions]] | ||
Latest revision as of 20:26, 29 May 2014
Introduction
This guide should help you in quickly setting up the X10 Remote Chime.
Setup
- Set the House code dial on the SC546A Remote Chime to the same letter as your X10 Controller (TM751 Transceiver Module, MT10A Mini Timer, etc.).
- Set the Unit Code dial on the SC546A to any unused number between 1 and 16. If you are using it with a Motion Sensor, set it to the same House and Unit Code as your Motion Sensor (MS13A/MS14A/MS16A) and the same House code as your Transceiver (TM751)--if you are using a Transceiver as opposed to the ActiveHome Professional software interface.
- Plug the SC546A Remote Chime into any unused outlet (not one that is controlled by a wall switch, in case the switch accidentally gets turned off).
- To test the SC546A, press the number button (on any X10 Controller) corresponding to its Unit Code. Or walk past a Motion Sensor. The Motion Sensor sends a signal to the TM751 (or CM15A interface), which retransmits it over your house wiring to the SC546A. The Remote Chime then sounds.