Difference between revisions of "MiniTimer Setup"

From X10Wiki
Jump to navigation Jump to search
 
(One intermediate revision by the same user not shown)
Line 1: Line 1:
 
==Question==
 
==Question==
  
−
'''How do I set up my MT10A MiniTimer?'''
+
'''How do I set up my MiniTimer?'''
  
 
==Answer==
 
==Answer==
  
−
Simply plug your MiniTimer into any AC outlet and set the clock by switching the Mode switch to "Set Clock" and use the rocking "Time" keys to set the time. 
+
===MT13A SETUP===
−
Adjust your Lamp or Appliance Modules to the same House code as the MiniTimer. You may need a screwdriver, kitchen knife, or the tip of an electrical prong to turn the dial. 
 
−
Set the Unit code on your Lamp or Appliance Module to any number between 1 and 8. The combination of your Unit and House code’s makes your module’s distinct address. This way your remote knows which modules to turn on and off. 
 
−
Set the Mode switch on the Mini Timer to the "run" position. 
 
−
Test that your lamp or appliance is correctly working by pressing the "On" rocker key on the Mini Timer key pad that corresponds to the Unit code number you set for your Lamp or Appliance Module above (use the Selector Switch to switch to 5 and 8). Press the rocker key to "Off" to then turn your lamp or appliance off. 
 
  
−
To program a timed event, first place the mode switch in the "Prog Set" position.
+
*Connect the power supply to the Mini Timer and plug the power supply into any convenient AC outlet.
−
Use the up and down arrows to advance to the desired time, then press any of the 4 ON or OFF rocker keys to set an on or off time for that Module. This will program the Mini Timer to turn that Module on (or off) at that time every day.
+
 
 +
 
 +
'''''NOTE:''' you must use the power supply that came with the Mini Timer. The power supply contains circuitry required to control your X10 modules, so you CANNOT replace it with a regular 12V power supply.''
 +
 
 +
 
 +
*Install two AA alkaline batteries in the compartment on the back, if desired (to protect the time and programmed events if there's a power outage).
 +
 
 +
*Set the MODE switch to “CLOCK SET.”
 +
 
 +
*Press the top of the “TIME” rocker to advance to the correct time. A quick press on the rocker will advance the time by 1 minute. If you hold the rocker down the display will advance to the correct time faster. If you overshoot, you can use the bottom rocker to go back.
 +
 
 +
*Adjust your Lamp or Appliance Modules to the same HouseCode as the MiniTimer. You may need a screwdriver to turn the dial.
 +
 +
*Set the UnitCode on your Lamp or Appliance Module to any number between 1 and 8. The combination of your Unit and House code’s makes your module’s distinct address. This way your timer knows which modules to turn ON/OFF. 
 +
 
 +
*Set the MODE switch on the MiniTimer to the "RUN" position.
 +
 
 +
*Test that your modules are working correctly by pressing the "ON" rocker key on the MiniTimer key pad that corresponds to the UnitCode number you set for your module above.
 +
 
 +
*Press the rocker key to "OFF" to then turn your lamp or appliance off.
 +
 
 +
 
 +
====Program a Timed Event====
 +
 
 +
*Place the MODE switch in the "PROG SET/REVIEW" position.
 +
 
 +
*Use the UP/DOWN arrows to advance to the desired time.
 +
 
 +
*Set the 1-4/5-8 switch to the desired position.
 +
 
 +
*Press any of the 4 ON/OFF rocker keys to set an ON/OFF time for that Module. This will program the Mini Timer to turn that Module ON/OFF at that time '''every day'''.
 +
 
 +
*Advance to another time, and press another ON or OFF button as desired.
 +
 
 +
*Set the MODE switch back to RUN.
 +
 
 +
 
 +
 
 +
===MT10A SETUP===
 +
 
 +
*Plug your MiniTimer into any AC outlet
 +
 
 +
*Set the clock by switching the MODE switch to "SET CLOCK" and use the rocking "TIME" keys to set the time.
 +
 +
*Adjust your Lamp or Appliance Modules to the same HouseCode as the MiniTimer. You may need a screwdriver, kitchen knife, or the tip of an electrical prong to turn the dial.
 +
 +
*Set the UnitCode on your Lamp or Appliance Module to any number between 1 and 8. The combination of your Unit and House code’s makes your module’s distinct address. This way your timer knows which modules to turn ON/OFF. 
 +
 
 +
*Set the MODE switch on the MiniTimer to the "RUN" position.
 +
 
 +
*Test that your modules are working correctly by pressing the "ON" rocker key on the MiniTimer key pad that corresponds to the UnitCode number you set for your module above.
 +
 
 +
*Press the rocker key to "OFF" to then turn your lamp or appliance off. 
 +
 
 +
 
 +
====Program a Timed Event====
 +
 
 +
*Place the MODE switch in the "PROG SET" position.
 +
 
 +
*Use the UP/DOWN arrows to advance to the desired time.
 +
 
 +
*Set the 1-4/5-8 switch to the desired position.
 +
 
 +
*Press any of the 4 ON/OFF rocker keys to set an ON/OFF time for that Module. This will program the Mini Timer to turn that Module ON/OFF at that time '''every day'''.

Latest revision as of 20:42, 20 May 2014

Question

How do I set up my MiniTimer?

Answer

MT13A SETUP

  • Connect the power supply to the Mini Timer and plug the power supply into any convenient AC outlet.


NOTE: you must use the power supply that came with the Mini Timer. The power supply contains circuitry required to control your X10 modules, so you CANNOT replace it with a regular 12V power supply.


  • Install two AA alkaline batteries in the compartment on the back, if desired (to protect the time and programmed events if there's a power outage).
  • Set the MODE switch to “CLOCK SET.”
  • Press the top of the “TIME” rocker to advance to the correct time. A quick press on the rocker will advance the time by 1 minute. If you hold the rocker down the display will advance to the correct time faster. If you overshoot, you can use the bottom rocker to go back.
  • Adjust your Lamp or Appliance Modules to the same HouseCode as the MiniTimer. You may need a screwdriver to turn the dial.
  • Set the UnitCode on your Lamp or Appliance Module to any number between 1 and 8. The combination of your Unit and House code’s makes your module’s distinct address. This way your timer knows which modules to turn ON/OFF.
  • Set the MODE switch on the MiniTimer to the "RUN" position.
  • Test that your modules are working correctly by pressing the "ON" rocker key on the MiniTimer key pad that corresponds to the UnitCode number you set for your module above.
  • Press the rocker key to "OFF" to then turn your lamp or appliance off.


Program a Timed Event

  • Place the MODE switch in the "PROG SET/REVIEW" position.
  • Use the UP/DOWN arrows to advance to the desired time.
  • Set the 1-4/5-8 switch to the desired position.
  • Press any of the 4 ON/OFF rocker keys to set an ON/OFF time for that Module. This will program the Mini Timer to turn that Module ON/OFF at that time every day.
  • Advance to another time, and press another ON or OFF button as desired.
  • Set the MODE switch back to RUN.


MT10A SETUP

  • Plug your MiniTimer into any AC outlet
  • Set the clock by switching the MODE switch to "SET CLOCK" and use the rocking "TIME" keys to set the time.
  • Adjust your Lamp or Appliance Modules to the same HouseCode as the MiniTimer. You may need a screwdriver, kitchen knife, or the tip of an electrical prong to turn the dial.
  • Set the UnitCode on your Lamp or Appliance Module to any number between 1 and 8. The combination of your Unit and House code’s makes your module’s distinct address. This way your timer knows which modules to turn ON/OFF.
  • Set the MODE switch on the MiniTimer to the "RUN" position.
  • Test that your modules are working correctly by pressing the "ON" rocker key on the MiniTimer key pad that corresponds to the UnitCode number you set for your module above.
  • Press the rocker key to "OFF" to then turn your lamp or appliance off.


Program a Timed Event

  • Place the MODE switch in the "PROG SET" position.
  • Use the UP/DOWN arrows to advance to the desired time.
  • Set the 1-4/5-8 switch to the desired position.
  • Press any of the 4 ON/OFF rocker keys to set an ON/OFF time for that Module. This will program the Mini Timer to turn that Module ON/OFF at that time every day.
Retrieved from "https://kbase.x10.com/index.php?title=MiniTimer_Setup&oldid=11236"