Difference between revisions of "VCR Commander & VCR Commander II Setup"
Jump to navigation
Jump to search
X10douglas (talk | contribs) |
X10douglas (talk | contribs) |
||
| Line 12: | Line 12: | ||
Press and hold the PLAY button until the LED stays on.<br> | Press and hold the PLAY button until the LED stays on.<br> | ||
Press the HOUSE button on your motion sensor. The LED on the VCR Commander will go out. | Press the HOUSE button on your motion sensor. The LED on the VCR Commander will go out. | ||
| − | |http://graphics.x10.com/images7/vcr_2.gif http://graphics.x10.com/images7/vcr_3.gif | + | |[[Image:http://graphics.x10.com/images7/vcr_2.gif http://graphics.x10.com/images7/vcr_3.gif]] |
|- | |- | ||
|'''Learn VCR Commands'''<br> | |'''Learn VCR Commands'''<br> | ||
Press and hold REC until the LED stays on. | Press and hold REC until the LED stays on. | ||
| − | |http://graphics.x10.com/images7/vcr_4.gif | + | |[[Image:http://graphics.x10.com/images7/vcr_4.gif]] |
|- | |- | ||
|Place your remote control 1 inch away from the VCR Commander. Press REC on the VCR Commander and release it. The LED will blink quickly and then stay on. Press the Record button on your remote and keep pressing it until the LED on the VCR Commander briefly goes out and comes back on solid. This means that Record has been learned. | |Place your remote control 1 inch away from the VCR Commander. Press REC on the VCR Commander and release it. The LED will blink quickly and then stay on. Press the Record button on your remote and keep pressing it until the LED on the VCR Commander briefly goes out and comes back on solid. This means that Record has been learned. | ||
Repeat these steps again for the STOP function. | Repeat these steps again for the STOP function. | ||
| − | |http://graphics.x10.com/images7/vcr_5.gif | + | |[[Image:http://graphics.x10.com/images7/vcr_5.gif]] |
|- | |- | ||
|'''Connect the Infrared Emitter Cable'''<br> | |'''Connect the Infrared Emitter Cable'''<br> | ||
Plug the IR emitter cable into the back of the VCR Commander.<br> | Plug the IR emitter cable into the back of the VCR Commander.<br> | ||
Press the emitter onto the VCR you are going to control, after removing the plastic from the adhesive backing. | Press the emitter onto the VCR you are going to control, after removing the plastic from the adhesive backing. | ||
| − | |http://graphics.x10.com/images7/vcr_6.gif http://graphics.x10.com/images7/vcr_7.gif | + | |[[Image:http://graphics.x10.com/images7/vcr_6.gif]] [[Image:http://graphics.x10.com/images7/vcr_7.gif]] |
|} | |} | ||
Congratulations! You are finished installing your VCR Commander. | Congratulations! You are finished installing your VCR Commander. | ||
| + | |||
| + | |||
==Related Articles== | ==Related Articles== | ||
| + | |||
[[Changing the Recording Time]] | [[Changing the Recording Time]] | ||
| − | + | ||
| − | |||
[[All Three IR Emitters Not Needed]] | [[All Three IR Emitters Not Needed]] | ||
| − | + | ||
| − | |||
[[Setting Up and Learning with VCR Commander]] | [[Setting Up and Learning with VCR Commander]] | ||
| − | |||
| − | |||
[[Category:frequently asked questions]] | [[Category:frequently asked questions]] | ||
Revision as of 02:02, 21 May 2014
Introduction
This guide should help you in quickly setting up the X10 VCR Commander & VCR Commander II.
Setup
| Find the box that contains the VCR Commander. Unpack the VCR Commander, its power supply and the Infrared (IR) Emitter cable. Connect the power supply to the VCR Commander and plug it into a wall outlet. | 
|
| Configure the Motion Sensor Code Press and hold the PLAY button until the LED stays on. |
File:Http://graphics.x10.com/images7/vcr 2.gif http://graphics.x10.com/images7/vcr 3.gif |
| Learn VCR Commands Press and hold REC until the LED stays on. |
File:Http://graphics.x10.com/images7/vcr 4.gif |
| Place your remote control 1 inch away from the VCR Commander. Press REC on the VCR Commander and release it. The LED will blink quickly and then stay on. Press the Record button on your remote and keep pressing it until the LED on the VCR Commander briefly goes out and comes back on solid. This means that Record has been learned.
Repeat these steps again for the STOP function. |
File:Http://graphics.x10.com/images7/vcr 5.gif |
| Connect the Infrared Emitter Cable Plug the IR emitter cable into the back of the VCR Commander. |
File:Http://graphics.x10.com/images7/vcr 6.gif File:Http://graphics.x10.com/images7/vcr 7.gif |
Congratulations! You are finished installing your VCR Commander.