Difference between revisions of "Problems Learning IR Codes"

From X10Wiki
Jump to navigation Jump to search
(Perl Automatic Add)
 
(2 intermediate revisions by 2 users not shown)
Line 1: Line 1:
Questions
+
==Question==
What should I do when my VCR Commander will not accept IR codes during programming?
+
 
Answer
+
'''What should I do when my VCR Commander will not accept IR codes during programming?'''
 +
 
 +
==Answer==
 +
 
 
If you are having trouble getting the VCR Commander to accept input from your remote, try the following:
 
If you are having trouble getting the VCR Commander to accept input from your remote, try the following:
 +
 
*Verify that the VCR Commander is connected to a functional outlet.
 
*Verify that the VCR Commander is connected to a functional outlet.
 
*Check that the IR emitter cable is NOT connected to it.
 
*Check that the IR emitter cable is NOT connected to it.
Line 8: Line 12:
 
*Aim the VCR remote at IR target on the back of the VCR Commander when sending commands.
 
*Aim the VCR remote at IR target on the back of the VCR Commander when sending commands.
 
*Always hold the VCR remote within one inch of this IR target.
 
*Always hold the VCR remote within one inch of this IR target.
*See if the UX21A/UX23A VCR Commander or VCR Commander II has been properly entered into �Learn IR� mode.
+
*See if the UX21A/UX23A VCR Commander or VCR Commander II has been properly entered into "Learn IR" mode.
 +
 
 +
 
 
After verifying each of the above steps, clear the IR memory in the VCR Commander and attempt to relearn the IR codes once more.
 
After verifying each of the above steps, clear the IR memory in the VCR Commander and attempt to relearn the IR codes once more.
'''#4:'''
+
 
[img src="http://graphics.x10.com/images_knowledgebase/a00044_01.jpg" border=2]
+
[[Image:a00044_01.jpg]]
Related Articles
+
 
[a href="/kbase/articles/a00039.html"]a00039[/a] : Setting Up and Learning with VCR Commander[BR]
+
 
Key Topics: ir, learn, command, commander, play, stop, record, remote, infrared
+
===Related Articles===
Relates to:
+
 
UX21A, UX23A, MS12A, MS13A, MS14A, MS16A
+
[[Setting Up and Learning with VCR Commander]]
[img src="http://site.x10.com/?Z3gxT2tiYXNlYXJ0aWNsZTEuZGF0=RND|kbasearticle"]
+
 
 +
 
 +
 
 +
[[Category:troubleshooting]]
 +
[[Category:frequently asked questions]]

Latest revision as of 22:05, 28 May 2014

Question

What should I do when my VCR Commander will not accept IR codes during programming?

Answer

If you are having trouble getting the VCR Commander to accept input from your remote, try the following:

  • Verify that the VCR Commander is connected to a functional outlet.
  • Check that the IR emitter cable is NOT connected to it.
  • Make sure that the batteries in VCR remote are no more than six months old.
  • Aim the VCR remote at IR target on the back of the VCR Commander when sending commands.
  • Always hold the VCR remote within one inch of this IR target.
  • See if the UX21A/UX23A VCR Commander or VCR Commander II has been properly entered into "Learn IR" mode.


After verifying each of the above steps, clear the IR memory in the VCR Commander and attempt to relearn the IR codes once more.

A00044 01.jpg


Related Articles

Setting Up and Learning with VCR Commander