Difference between revisions of "Protector Plus (DS7000) Message Dialer Quick Setup"
Jump to navigation
Jump to search
X10MichaelC (talk | contribs) |
(Perl Automatic Add) |
||
| Line 1: | Line 1: | ||
| − | + | Questions | |
| − | + | How do I setup my security system? | |
| − | [ | + | How do I program phone numbers in the console? |
| + | Answer | ||
| + | Here are some quick instructions for setting up the telephone dialer. | ||
| + | *Set the console's INSTALL/RUN switch to INSTALL. | ||
| + | *Press the PROG button. | ||
| + | *Enter the first phone number that you want the console to call in the event of a problem, e.g. 234-5678. | ||
| + | *Press the MEM button. | ||
| + | *Press 1 to store the phone number in memory location 1. | ||
| + | *Press PROG and enter a second number, followed by pressing MEM and then 2 to store the number in memory location 2. | ||
| + | *Press PROG and enter a third number, followed by pressing MEM and then 3 to store the number in memory location 3. | ||
| + | *Press PROG and enter a fourth number, followed by pressing MEM and then 4 to store the number in memory location 4. | ||
| + | *Repeat steps 1-5 to change a number. | ||
| + | *When you are finished programming the numbers, move the console's INSTALL/RUN switch back to RUN. | ||
| + | If you want to store only one number, 'fill up' the memory locations with that number. | ||
| + | Ex: | ||
| + | 234-5678 memory location 1. | ||
| + | 234-5678 memory location 2. | ||
| + | 234-5678 memory location 3. | ||
| + | 234-5678 memory location 4. | ||
| + | To store a voice message: | ||
| + | *Plug an earphone into the jack on the side of the console. | ||
| + | *Set the console's INSTALL/RUN switch to INSTALL. | ||
| + | *Press the RECORD button. The RECORD light turns on. | ||
| + | *Speak clearly into the microphone on the front of the console. You can record up to 15 seconds of speech. Ex: "This is Mrs Smith. There's a strange noise in my house. Press 0 to listen." After 15 seconds the RECORD light turns off. | ||
| + | *Set the console's INSTALL/RUN switch to RUN. The console plays back your message through the earphone so you can hear what it sounds like (it sounds better over the phone). | ||
| + | *If you want to hear the message again, set the console's INSTALL/RUN switch to INSTALL and then back to RUN. | ||
| + | Repeat all the steps if you want to change the message. | ||
| + | Related Articles | ||
| + | [img src="http://site.x10.com/?Z3gxT2tiYXNlYXJ0aWNsZTEuZGF0=RND|kbasearticle"] | ||
Revision as of 22:17, 16 March 2006
Questions How do I setup my security system? How do I program phone numbers in the console? Answer Here are some quick instructions for setting up the telephone dialer.
- Set the console's INSTALL/RUN switch to INSTALL.
- Press the PROG button.
- Enter the first phone number that you want the console to call in the event of a problem, e.g. 234-5678.
- Press the MEM button.
- Press 1 to store the phone number in memory location 1.
- Press PROG and enter a second number, followed by pressing MEM and then 2 to store the number in memory location 2.
- Press PROG and enter a third number, followed by pressing MEM and then 3 to store the number in memory location 3.
- Press PROG and enter a fourth number, followed by pressing MEM and then 4 to store the number in memory location 4.
- Repeat steps 1-5 to change a number.
- When you are finished programming the numbers, move the console's INSTALL/RUN switch back to RUN.
If you want to store only one number, 'fill up' the memory locations with that number. Ex: 234-5678 memory location 1. 234-5678 memory location 2. 234-5678 memory location 3. 234-5678 memory location 4. To store a voice message:
- Plug an earphone into the jack on the side of the console.
- Set the console's INSTALL/RUN switch to INSTALL.
- Press the RECORD button. The RECORD light turns on.
- Speak clearly into the microphone on the front of the console. You can record up to 15 seconds of speech. Ex: "This is Mrs Smith. There's a strange noise in my house. Press 0 to listen." After 15 seconds the RECORD light turns off.
- Set the console's INSTALL/RUN switch to RUN. The console plays back your message through the earphone so you can hear what it sounds like (it sounds better over the phone).
- If you want to hear the message again, set the console's INSTALL/RUN switch to INSTALL and then back to RUN.
Repeat all the steps if you want to change the message. Related Articles [img src="http://site.x10.com/?Z3gxT2tiYXNlYXJ0aWNsZTEuZGF0=RND%7Ckbasearticle"]