Difference between revisions of "Setting Motion Off Delay Time"
(→Answer) |
X10douglas (talk | contribs) |
||
| (2 intermediate revisions by 2 users not shown) | |||
| Line 5: | Line 5: | ||
==Answer== | ==Answer== | ||
| − | You can set the delay time before your home automation motion sensor | + | You can set the delay time before your home automation motion sensor sends an Off command after turning a module on. |
| − | button. The green LED light turns on. 3 seconds later the red LED light reports the delay setting as follows: | + | |
| + | To check the current Off command delay time, press the House/On button once. | ||
| + | |||
| + | The red LED light should flash. Press and hold the Unit/Off button. | ||
| + | |||
| + | The green LED light turns on. | ||
| + | |||
| + | 3 seconds later the red LED light reports the delay setting as follows: | ||
| + | |||
*1 blink for 1 minute. | *1 blink for 1 minute. | ||
*2 blinks for 2 minutes. | *2 blinks for 2 minutes. | ||
| Line 16: | Line 24: | ||
*8 blinks for 128 minutes. | *8 blinks for 128 minutes. | ||
*9 blinks for 256 minutes. | *9 blinks for 256 minutes. | ||
| − | To change this, Press the House/On button once. The red LED light will flash. Press and hold the Unit/Off button. The green LED light turns on. Three seconds later the red LED light reports the delay setting, as shown above. Release and immediately press the Unit/Off button the number of times for the delay you want. Hold the button for 3 seconds after the last press. The red LED light then reports the setting with the appropriate number of flashes. Release the button, and you are all set up. | + | |
| + | |||
| + | To change this, Press the House/On button once. The red LED light will flash. Press and hold the Unit/Off button. The green LED light turns on. Three seconds later the red LED light reports the delay setting, as shown above. | ||
| + | |||
| + | Release and immediately press the Unit/Off button the number of times for the delay you want. | ||
| + | |||
| + | Hold the button for 3 seconds after the last press. | ||
| + | |||
| + | The red LED light then reports the setting with the appropriate number of flashes. | ||
| + | |||
| + | Release the button, and you are all set up. | ||
| + | |||
| + | |||
===Related Articles=== | ===Related Articles=== | ||
| + | |||
| + | [[Setting Motion Off Delay Time For ActiveEye]] | ||
[[Category:troubleshooting]] | [[Category:troubleshooting]] | ||
[[Category:frequently asked questions]] | [[Category:frequently asked questions]] | ||
Latest revision as of 19:31, 29 May 2014
Question
How do I set the Off Delay Time on my MS13A/MS14A motion sensor?
Answer
You can set the delay time before your home automation motion sensor sends an Off command after turning a module on.
To check the current Off command delay time, press the House/On button once.
The red LED light should flash. Press and hold the Unit/Off button.
The green LED light turns on.
3 seconds later the red LED light reports the delay setting as follows:
- 1 blink for 1 minute.
- 2 blinks for 2 minutes.
- 3 blinks for 4 minutes.
- 4 blinks for 8 minutes.
- 5 blinks for 16 minutes.
- 6 blinks for 32 minutes.
- 7 blinks for 64 minutes.
- 8 blinks for 128 minutes.
- 9 blinks for 256 minutes.
To change this, Press the House/On button once. The red LED light will flash. Press and hold the Unit/Off button. The green LED light turns on. Three seconds later the red LED light reports the delay setting, as shown above.
Release and immediately press the Unit/Off button the number of times for the delay you want.
Hold the button for 3 seconds after the last press.
The red LED light then reports the setting with the appropriate number of flashes.
Release the button, and you are all set up.