FloodCam Troubleshooting
Jump to navigation
Jump to search
Question
Why ain't it workin' right?
Answer
If you have problems answering these questions, please refer to this document.
1) Have you installed your FloodCam?
- YES: Go to step 2.
- NO: Please read FloodCam Installation.
2) Does your FloodCam problem involve the behavior of the lights/motion sensor, or is it an issue with the camera picture?
- LIGHTS: Go to step 3.
- CAMERA: Go to step 8.
- CLEARLY NOT EITHER: Go to step 15.
3) When the FloodCam is initially connected to power, are the lights on immediately?
- YES: Please call 800-442-5138. Your FloodCam may have an issue.
- NO: Go to step 4.
4) Is the FloodCam not turning off when it is turned on by motion?
- YES: Go to step 5.
- NO: Go to step 7.
5) Turn the FLOODLIGHT CONTROL all the way counterclockwise; turn the TIME DELAY all the way clockwise. If you trip the FloodCam's sensor, do the lights come on?
- YES: Go to step 6.
- NO/"the dials just keep spinning": Please call 800-442-5138. Your FloodCam may have an issue.
6) OK, now cover the sensor completely with a cloth. Do the lights go off eventually?
- YES: Floodlights Don't Turn_Off ; see last paragraph; email techpriority@x10.com otherwise.
- NO: Please call 800-442-5138. Your FloodCam may have an issue.
7) Do you have an X10 remote control, computer module, or plug-in controller? Does the FloodCam respond correctly to it?
- initial NO: What is the FloodCam not doing correctly? ->techpriority@x10.com
- YES then NO: Troubleshooting Camera Switching
- YES then YES: What is the FloodCam not doing correctly? ->techpriority@x10.com
8) Is your Video Receiver connected to a PC or a TV?
- PC: Go to step 50.
- TV: Go to step 9.
9) Do you see a picture from your camera on your TV when you turn the Video Receiver on?
- NO: Review this article then go to step 4.
- SORT OF: Go to step 10.
- YES: Go to step 11.
10) Do you have more than one X10 camera set to the same A-D transmission channel as the FloodCam and connected to power?
11) Do you have more than one X10 camera set to the same A-D transmission channel as the FloodCam and connected to power?
- YES: Go to step 12.
- NO: Go to step 14.
12) Can you switch between cameras using an X10 remote control?
- YES: Go to step 16.
- NO: Troubleshooting Camera Switching
13) How far is the FloodCam from the Video Receiver? What is between the cam and receiver?
- LESS THAN 40 FEET/ WOOD AND SHEETROCK, ETC: Troubleshooting Floodcam Picture on TV
- OVER 40 FEET/ METAL OR CONCRETE OR CERAMIC: Camera Range Extending Wireless Camera Range
14) Do you have access to a TV?
- YES: Let's test things on the TV first. Please connect the Video Receiver to your TV and set it to the appropriate channel. Go to step 7.
- NO: Please read Troubleshooting Video Display Errors on PC.
15) Let me clear up some common questions. The FloodCam needs 110V AC wall power, including a neutral wire, to work; it does not have a microphone or broadcast audio; it is not a night-vision camera, but is dependent on its attached floodlights to produce a picture in low light.
- Please contact techical support at 800-442-5138 or techpriority@x10.com. Explain what you want your FloodCam to do and what it is doing instead.
16) Let me clear up some common questions. The FloodCam does not have a microphone or broadcast audio. It is not a night-vision camera, but is dependent on its attached floodlights to produce a picture in low light.
- Please contact techical support at 800-442-5138 or techpriority@x10.com. Explain what you want your FloodCam to do and what it is doing instead.
If you have problems answering these questions, please refer to this document.